/* ============================================================================ */
/* Copyright (c) 2015, Texas Instruments Incorporated                           */
/*  All rights reserved.                                                        */
/*                                                                              */
/*  Redistribution and use in source and binary forms, with or without          */
/*  modification, are permitted provided that the following conditions          */
/*  are met:                                                                    */
/*                                                                              */
/*  *  Redistributions of source code must retain the above copyright           */
/*     notice, this list of conditions and the following disclaimer.            */
/*                                                                              */
/*  *  Redistributions in binary form must reproduce the above copyright        */
/*     notice, this list of conditions and the following disclaimer in the      */
/*     documentation and/or other materials provided with the distribution.     */
/*                                                                              */
/*  *  Neither the name of Texas Instruments Incorporated nor the names of      */
/*     its contributors may be used to endorse or promote products derived      */
/*     from this software without specific prior written permission.            */
/*                                                                              */
/*  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" */
/*  AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,       */
/*  THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR      */
/*  PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR            */
/*  CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,       */
/*  EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,         */
/*  PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; */
/*  OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,    */
/*  WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR     */
/*  OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,              */
/*  EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.                          */
/* ============================================================================ */

/********************************************************************
*
* Standard register and bit definitions for the Texas Instruments
* MSP430 microcontroller.
*
* This file supports assembler and C development for
* MSP430G2302 devices.
*
* Texas Instruments, Version 1.0
*
* Rev. 1.0, Setup
*
********************************************************************/

#ifndef __MSP430G2302
#define __MSP430G2302

#define __MSP430_HEADER_VERSION__ 1167

#define __MSP430_TI_HEADERS__

#ifdef __cplusplus
extern "C" {
#endif

#include <iomacros.h>

/************************************************************
* STANDARD BITS
************************************************************/

#define BIT0                (0x0001)
#define BIT1                (0x0002)
#define BIT2                (0x0004)
#define BIT3                (0x0008)
#define BIT4                (0x0010)
#define BIT5                (0x0020)
#define BIT6                (0x0040)
#define BIT7                (0x0080)
#define BIT8                (0x0100)
#define BIT9                (0x0200)
#define BITA                (0x0400)
#define BITB                (0x0800)
#define BITC                (0x1000)
#define BITD                (0x2000)
#define BITE                (0x4000)
#define BITF                (0x8000)

/************************************************************
* STATUS REGISTER BITS
************************************************************/

#define C                   (0x0001)
#define Z                   (0x0002)
#define N                   (0x0004)
#define V                   (0x0100)
#define GIE                 (0x0008)
#define CPUOFF              (0x0010)
#define OSCOFF              (0x0020)
#define SCG0                (0x0040)
#define SCG1                (0x0080)

/* Low Power Modes coded with Bits 4-7 in SR */

#ifndef __STDC__ /* Begin #defines for assembler */
#define LPM0                (CPUOFF)
#define LPM1                (SCG0+CPUOFF)
#define LPM2                (SCG1+CPUOFF)
#define LPM3                (SCG1+SCG0+CPUOFF)
#define LPM4                (SCG1+SCG0+OSCOFF+CPUOFF)
/* End #defines for assembler */

#else /* Begin #defines for C */
#define LPM0_bits           (CPUOFF)
#define LPM1_bits           (SCG0+CPUOFF)
#define LPM2_bits           (SCG1+CPUOFF)
#define LPM3_bits           (SCG1+SCG0+CPUOFF)
#define LPM4_bits           (SCG1+SCG0+OSCOFF+CPUOFF)

#include "in430.h"

#define LPM0      __bis_SR_register(LPM0_bits)         /* Enter Low Power Mode 0 */
#define LPM0_EXIT __bic_SR_register_on_exit(LPM0_bits) /* Exit Low Power Mode 0 */
#define LPM1      __bis_SR_register(LPM1_bits)         /* Enter Low Power Mode 1 */
#define LPM1_EXIT __bic_SR_register_on_exit(LPM1_bits) /* Exit Low Power Mode 1 */
#define LPM2      __bis_SR_register(LPM2_bits)         /* Enter Low Power Mode 2 */
#define LPM2_EXIT __bic_SR_register_on_exit(LPM2_bits) /* Exit Low Power Mode 2 */
#define LPM3      __bis_SR_register(LPM3_bits)         /* Enter Low Power Mode 3 */
#define LPM3_EXIT __bic_SR_register_on_exit(LPM3_bits) /* Exit Low Power Mode 3 */
#define LPM4      __bis_SR_register(LPM4_bits)         /* Enter Low Power Mode 4 */
#define LPM4_EXIT __bic_SR_register_on_exit(LPM4_bits) /* Exit Low Power Mode 4 */
#endif /* End #defines for C */

/************************************************************
* PERIPHERAL FILE MAP
************************************************************/

/************************************************************
* SPECIAL FUNCTION REGISTER ADDRESSES + CONTROL BITS
************************************************************/

#define IE1_                  0x0000    /* Interrupt Enable 1 */
sfrb(IE1, IE1_);
#define WDTIE               (0x01)    /* Watchdog Interrupt Enable */
#define OFIE                (0x02)    /* Osc. Fault  Interrupt Enable */
#define NMIIE               (0x10)    /* NMI Interrupt Enable */
#define ACCVIE              (0x20)    /* Flash Access Violation Interrupt Enable */

#define IFG1_                 0x0002    /* Interrupt Flag 1 */
sfrb(IFG1, IFG1_);
#define WDTIFG              (0x01)    /* Watchdog Interrupt Flag */
#define OFIFG               (0x02)    /* Osc. Fault Interrupt Flag */
#define PORIFG              (0x04)    /* Power On Interrupt Flag */
#define RSTIFG              (0x08)    /* Reset Interrupt Flag */
#define NMIIFG              (0x10)    /* NMI Interrupt Flag */


/************************************************************
* Basic Clock Module
************************************************************/
#define __MSP430_HAS_BC2__            /* Definition to show that Module is available */

#define DCOCTL_               0x0056    /* DCO Clock Frequency Control */
sfrb(DCOCTL, DCOCTL_);
#define BCSCTL1_              0x0057    /* Basic Clock System Control 1 */
sfrb(BCSCTL1, BCSCTL1_);
#define BCSCTL2_              0x0058    /* Basic Clock System Control 2 */
sfrb(BCSCTL2, BCSCTL2_);
#define BCSCTL3_              0x0053    /* Basic Clock System Control 3 */
sfrb(BCSCTL3, BCSCTL3_);

#define MOD0                (0x01)   /* Modulation Bit 0 */
#define MOD1                (0x02)   /* Modulation Bit 1 */
#define MOD2                (0x04)   /* Modulation Bit 2 */
#define MOD3                (0x08)   /* Modulation Bit 3 */
#define MOD4                (0x10)   /* Modulation Bit 4 */
#define DCO0                (0x20)   /* DCO Select Bit 0 */
#define DCO1                (0x40)   /* DCO Select Bit 1 */
#define DCO2                (0x80)   /* DCO Select Bit 2 */

#define RSEL0               (0x01)   /* Range Select Bit 0 */
#define RSEL1               (0x02)   /* Range Select Bit 1 */
#define RSEL2               (0x04)   /* Range Select Bit 2 */
#define RSEL3               (0x08)   /* Range Select Bit 3 */
#define DIVA0               (0x10)   /* ACLK Divider 0 */
#define DIVA1               (0x20)   /* ACLK Divider 1 */
#define XTS                 (0x40)   /* LFXTCLK 0:Low Freq. / 1: High Freq. */
#define XT2OFF              (0x80)   /* Enable XT2CLK */

#define DIVA_0              (0x00)   /* ACLK Divider 0: /1 */
#define DIVA_1              (0x10)   /* ACLK Divider 1: /2 */
#define DIVA_2              (0x20)   /* ACLK Divider 2: /4 */
#define DIVA_3              (0x30)   /* ACLK Divider 3: /8 */

#define DIVS0               (0x02)   /* SMCLK Divider 0 */
#define DIVS1               (0x04)   /* SMCLK Divider 1 */
#define SELS                (0x08)   /* SMCLK Source Select 0:DCOCLK / 1:XT2CLK/LFXTCLK */
#define DIVM0               (0x10)   /* MCLK Divider 0 */
#define DIVM1               (0x20)   /* MCLK Divider 1 */
#define SELM0               (0x40)   /* MCLK Source Select 0 */
#define SELM1               (0x80)   /* MCLK Source Select 1 */

#define DIVS_0              (0x00)   /* SMCLK Divider 0: /1 */
#define DIVS_1              (0x02)   /* SMCLK Divider 1: /2 */
#define DIVS_2              (0x04)   /* SMCLK Divider 2: /4 */
#define DIVS_3              (0x06)   /* SMCLK Divider 3: /8 */

#define DIVM_0              (0x00)   /* MCLK Divider 0: /1 */
#define DIVM_1              (0x10)   /* MCLK Divider 1: /2 */
#define DIVM_2              (0x20)   /* MCLK Divider 2: /4 */
#define DIVM_3              (0x30)   /* MCLK Divider 3: /8 */

#define SELM_0              (0x00)   /* MCLK Source Select 0: DCOCLK */
#define SELM_1              (0x40)   /* MCLK Source Select 1: DCOCLK */
#define SELM_2              (0x80)   /* MCLK Source Select 2: XT2CLK/LFXTCLK */
#define SELM_3              (0xC0)   /* MCLK Source Select 3: LFXTCLK */

#define LFXT1OF             (0x01)   /* Low/high Frequency Oscillator Fault Flag */
#define XT2OF               (0x02)   /* High frequency oscillator 2 fault flag */
#define XCAP0               (0x04)   /* XIN/XOUT Cap 0 */
#define XCAP1               (0x08)   /* XIN/XOUT Cap 1 */
#define LFXT1S0             (0x10)   /* Mode 0 for LFXT1 (XTS = 0) */
#define LFXT1S1             (0x20)   /* Mode 1 for LFXT1 (XTS = 0) */
#define XT2S0               (0x40)   /* Mode 0 for XT2 */
#define XT2S1               (0x80)   /* Mode 1 for XT2 */

#define XCAP_0              (0x00)   /* XIN/XOUT Cap : 0 pF */
#define XCAP_1              (0x04)   /* XIN/XOUT Cap : 6 pF */
#define XCAP_2              (0x08)   /* XIN/XOUT Cap : 10 pF */
#define XCAP_3              (0x0C)   /* XIN/XOUT Cap : 12.5 pF */

#define LFXT1S_0            (0x00)   /* Mode 0 for LFXT1 : Normal operation */
#define LFXT1S_1            (0x10)   /* Mode 1 for LFXT1 : Reserved */
#define LFXT1S_2            (0x20)   /* Mode 2 for LFXT1 : VLO */
#define LFXT1S_3            (0x30)   /* Mode 3 for LFXT1 : Digital input signal */

#define XT2S_0              (0x00)   /* Mode 0 for XT2 : 0.4 - 1 MHz */
#define XT2S_1              (0x40)   /* Mode 1 for XT2 : 1 - 4 MHz */
#define XT2S_2              (0x80)   /* Mode 2 for XT2 : 2 - 16 MHz */
#define XT2S_3              (0xC0)   /* Mode 3 for XT2 : Digital input signal */

/*************************************************************
* Flash Memory
*************************************************************/
#define __MSP430_HAS_FLASH2__         /* Definition to show that Module is available */

#define FCTL1_                0x0128    /* FLASH Control 1 */
sfrw(FCTL1, FCTL1_);
#define FCTL2_                0x012A    /* FLASH Control 2 */
sfrw(FCTL2, FCTL2_);
#define FCTL3_                0x012C    /* FLASH Control 3 */
sfrw(FCTL3, FCTL3_);

#define FRKEY               (0x9600)  /* Flash key returned by read */
#define FWKEY               (0xA500)  /* Flash key for write */
#define FXKEY               (0x3300)  /* for use with XOR instruction */

#define ERASE               (0x0002)  /* Enable bit for Flash segment erase */
#define MERAS               (0x0004)  /* Enable bit for Flash mass erase */
#define WRT                 (0x0040)  /* Enable bit for Flash write */
#define BLKWRT              (0x0080)  /* Enable bit for Flash segment write */
#define SEGWRT              (0x0080)  /* old definition */ /* Enable bit for Flash segment write */

#define FN0                 (0x0001)  /* Divide Flash clock by 1 to 64 using FN0 to FN5 according to: */
#define FN1                 (0x0002)  /*  32*FN5 + 16*FN4 + 8*FN3 + 4*FN2 + 2*FN1 + FN0 + 1 */
#ifndef FN2
#define FN2                 (0x0004)
#endif
#ifndef FN3
#define FN3                 (0x0008)
#endif
#ifndef FN4
#define FN4                 (0x0010)
#endif
#define FN5                 (0x0020)
#define FSSEL0              (0x0040)  /* Flash clock select 0 */        /* to distinguish from USART SSELx */
#define FSSEL1              (0x0080)  /* Flash clock select 1 */

#define FSSEL_0             (0x0000)  /* Flash clock select: 0 - ACLK */
#define FSSEL_1             (0x0040)  /* Flash clock select: 1 - MCLK */
#define FSSEL_2             (0x0080)  /* Flash clock select: 2 - SMCLK */
#define FSSEL_3             (0x00C0)  /* Flash clock select: 3 - SMCLK */

#define BUSY                (0x0001)  /* Flash busy: 1 */
#define KEYV                (0x0002)  /* Flash Key violation flag */
#define ACCVIFG             (0x0004)  /* Flash Access violation flag */
#define WAIT                (0x0008)  /* Wait flag for segment write */
#define LOCK                (0x0010)  /* Lock bit: 1 - Flash is locked (read only) */
#define EMEX                (0x0020)  /* Flash Emergency Exit */
#define LOCKA               (0x0040)  /* Segment A Lock bit: read = 1 - Segment is locked (read only) */
#define FAIL                (0x0080)  /* Last Program or Erase failed */

/************************************************************
* DIGITAL I/O Port1/2 Pull up / Pull down Resistors
************************************************************/
#define __MSP430_HAS_PORT1_R__        /* Definition to show that Module is available */
#define __MSP430_HAS_PORT2_R__        /* Definition to show that Module is available */

#define P1IN_                 0x0020    /* Port 1 Input */
const_sfrb(P1IN, P1IN_);
#define P1OUT_                0x0021    /* Port 1 Output */
sfrb(P1OUT, P1OUT_);
#define P1DIR_                0x0022    /* Port 1 Direction */
sfrb(P1DIR, P1DIR_);
#define P1IFG_                0x0023    /* Port 1 Interrupt Flag */
sfrb(P1IFG, P1IFG_);
#define P1IES_                0x0024    /* Port 1 Interrupt Edge Select */
sfrb(P1IES, P1IES_);
#define P1IE_                 0x0025    /* Port 1 Interrupt Enable */
sfrb(P1IE, P1IE_);
#define P1SEL_                0x0026    /* Port 1 Selection */
sfrb(P1SEL, P1SEL_);
#define P1SEL2_               0x0041    /* Port 1 Selection 2 */
sfrb(P1SEL2, P1SEL2_);
#define P1REN_                0x0027    /* Port 1 Resistor Enable */
sfrb(P1REN, P1REN_);

#define P2IN_                 0x0028    /* Port 2 Input */
const_sfrb(P2IN, P2IN_);
#define P2OUT_                0x0029    /* Port 2 Output */
sfrb(P2OUT, P2OUT_);
#define P2DIR_                0x002A    /* Port 2 Direction */
sfrb(P2DIR, P2DIR_);
#define P2IFG_                0x002B    /* Port 2 Interrupt Flag */
sfrb(P2IFG, P2IFG_);
#define P2IES_                0x002C    /* Port 2 Interrupt Edge Select */
sfrb(P2IES, P2IES_);
#define P2IE_                 0x002D    /* Port 2 Interrupt Enable */
sfrb(P2IE, P2IE_);
#define P2SEL_                0x002E    /* Port 2 Selection */
sfrb(P2SEL, P2SEL_);
#define P2SEL2_               0x0042    /* Port 2 Selection 2 */
sfrb(P2SEL2, P2SEL2_);
#define P2REN_                0x002F    /* Port 2 Resistor Enable */
sfrb(P2REN, P2REN_);

/************************************************************
* Timer0_A3
************************************************************/
#define __MSP430_HAS_TA3__            /* Definition to show that Module is available */

#define TA0IV_                0x012E    /* Timer0_A3 Interrupt Vector Word */
const_sfrw(TA0IV, TA0IV_);
#define TA0CTL_               0x0160    /* Timer0_A3 Control */
sfrw(TA0CTL, TA0CTL_);
#define TA0CCTL0_             0x0162    /* Timer0_A3 Capture/Compare Control 0 */
sfrw(TA0CCTL0, TA0CCTL0_);
#define TA0CCTL1_             0x0164    /* Timer0_A3 Capture/Compare Control 1 */
sfrw(TA0CCTL1, TA0CCTL1_);
#define TA0CCTL2_             0x0166    /* Timer0_A3 Capture/Compare Control 2 */
sfrw(TA0CCTL2, TA0CCTL2_);
#define TA0R_                 0x0170    /* Timer0_A3 Counter Register */
sfrw(TA0R, TA0R_);
#define TA0CCR0_              0x0172    /* Timer0_A3 Capture/Compare 0 */
sfrw(TA0CCR0, TA0CCR0_);
#define TA0CCR1_              0x0174    /* Timer0_A3 Capture/Compare 1 */
sfrw(TA0CCR1, TA0CCR1_);
#define TA0CCR2_              0x0176    /* Timer0_A3 Capture/Compare 2 */
sfrw(TA0CCR2, TA0CCR2_);

/* Alternate register names */
#define TAIV                TA0IV     /* Timer A Interrupt Vector Word */
#define TACTL               TA0CTL    /* Timer A Control */
#define TACCTL0             TA0CCTL0  /* Timer A Capture/Compare Control 0 */
#define TACCTL1             TA0CCTL1  /* Timer A Capture/Compare Control 1 */
#define TACCTL2             TA0CCTL2  /* Timer A Capture/Compare Control 2 */
#define TAR                 TA0R      /* Timer A Counter Register */
#define TACCR0              TA0CCR0   /* Timer A Capture/Compare 0 */
#define TACCR1              TA0CCR1   /* Timer A Capture/Compare 1 */
#define TACCR2              TA0CCR2   /* Timer A Capture/Compare 2 */
#define TAIV_               TA0IV_    /* Timer A Interrupt Vector Word */
#define TACTL_              TA0CTL_   /* Timer A Control */
#define TACCTL0_            TA0CCTL0_ /* Timer A Capture/Compare Control 0 */
#define TACCTL1_            TA0CCTL1_ /* Timer A Capture/Compare Control 1 */
#define TACCTL2_            TA0CCTL2_ /* Timer A Capture/Compare Control 2 */
#define TAR_                TA0R_     /* Timer A Counter Register */
#define TACCR0_             TA0CCR0_  /* Timer A Capture/Compare 0 */
#define TACCR1_             TA0CCR1_  /* Timer A Capture/Compare 1 */
#define TACCR2_             TA0CCR2_  /* Timer A Capture/Compare 2 */

/* Alternate register names 2 */
#define CCTL0               TACCTL0   /* Timer A Capture/Compare Control 0 */
#define CCTL1               TACCTL1   /* Timer A Capture/Compare Control 1 */
#define CCTL2               TACCTL2   /* Timer A Capture/Compare Control 2 */
#define CCR0                TACCR0    /* Timer A Capture/Compare 0 */
#define CCR1                TACCR1    /* Timer A Capture/Compare 1 */
#define CCR2                TACCR2    /* Timer A Capture/Compare 2 */
#define CCTL0_              TACCTL0_  /* Timer A Capture/Compare Control 0 */
#define CCTL1_              TACCTL1_  /* Timer A Capture/Compare Control 1 */
#define CCTL2_              TACCTL2_  /* Timer A Capture/Compare Control 2 */
#define CCR0_               TACCR0_   /* Timer A Capture/Compare 0 */
#define CCR1_               TACCR1_   /* Timer A Capture/Compare 1 */
#define CCR2_               TACCR2_   /* Timer A Capture/Compare 2 */

#define TASSEL1             (0x0200)  /* Timer A clock source select 1 */
#define TASSEL0             (0x0100)  /* Timer A clock source select 0 */
#define ID1                 (0x0080)  /* Timer A clock input divider 1 */
#define ID0                 (0x0040)  /* Timer A clock input divider 0 */
#define MC1                 (0x0020)  /* Timer A mode control 1 */
#define MC0                 (0x0010)  /* Timer A mode control 0 */
#define TACLR               (0x0004)  /* Timer A counter clear */
#define TAIE                (0x0002)  /* Timer A counter interrupt enable */
#define TAIFG               (0x0001)  /* Timer A counter interrupt flag */

#define MC_0                (0x0000)  /* Timer A mode control: 0 - Stop */
#define MC_1                (0x0010)  /* Timer A mode control: 1 - Up to CCR0 */
#define MC_2                (0x0020)  /* Timer A mode control: 2 - Continous up */
#define MC_3                (0x0030)  /* Timer A mode control: 3 - Up/Down */
#define ID_0                (0x0000)  /* Timer A input divider: 0 - /1 */
#define ID_1                (0x0040)  /* Timer A input divider: 1 - /2 */
#define ID_2                (0x0080)  /* Timer A input divider: 2 - /4 */
#define ID_3                (0x00C0)  /* Timer A input divider: 3 - /8 */
#define TASSEL_0            (0x0000) /* Timer A clock source select: 0 - TACLK */
#define TASSEL_1            (0x0100) /* Timer A clock source select: 1 - ACLK  */
#define TASSEL_2            (0x0200) /* Timer A clock source select: 2 - SMCLK */
#define TASSEL_3            (0x0300) /* Timer A clock source select: 3 - INCLK */

#define CM1                 (0x8000)  /* Capture mode 1 */
#define CM0                 (0x4000)  /* Capture mode 0 */
#define CCIS1               (0x2000)  /* Capture input select 1 */
#define CCIS0               (0x1000)  /* Capture input select 0 */
#define SCS                 (0x0800)  /* Capture sychronize */
#define SCCI                (0x0400)  /* Latched capture signal (read) */
#define CAP                 (0x0100)  /* Capture mode: 1 /Compare mode : 0 */
#define OUTMOD2             (0x0080)  /* Output mode 2 */
#define OUTMOD1             (0x0040)  /* Output mode 1 */
#define OUTMOD0             (0x0020)  /* Output mode 0 */
#define CCIE                (0x0010)  /* Capture/compare interrupt enable */
#define CCI                 (0x0008)  /* Capture input signal (read) */
#define OUT                 (0x0004)  /* PWM Output signal if output mode 0 */
#define COV                 (0x0002)  /* Capture/compare overflow flag */
#define CCIFG               (0x0001)  /* Capture/compare interrupt flag */

#define OUTMOD_0            (0x0000)  /* PWM output mode: 0 - output only */
#define OUTMOD_1            (0x0020)  /* PWM output mode: 1 - set */
#define OUTMOD_2            (0x0040)  /* PWM output mode: 2 - PWM toggle/reset */
#define OUTMOD_3            (0x0060)  /* PWM output mode: 3 - PWM set/reset */
#define OUTMOD_4            (0x0080)  /* PWM output mode: 4 - toggle */
#define OUTMOD_5            (0x00A0)  /* PWM output mode: 5 - Reset */
#define OUTMOD_6            (0x00C0)  /* PWM output mode: 6 - PWM toggle/set */
#define OUTMOD_7            (0x00E0)  /* PWM output mode: 7 - PWM reset/set */
#define CCIS_0              (0x0000) /* Capture input select: 0 - CCIxA */
#define CCIS_1              (0x1000) /* Capture input select: 1 - CCIxB */
#define CCIS_2              (0x2000) /* Capture input select: 2 - GND */
#define CCIS_3              (0x3000) /* Capture input select: 3 - Vcc */
#define CM_0                (0x0000) /* Capture mode: 0 - disabled */
#define CM_1                (0x4000) /* Capture mode: 1 - pos. edge */
#define CM_2                (0x8000) /* Capture mode: 1 - neg. edge */
#define CM_3                (0xC000) /* Capture mode: 1 - both edges */

/* T0_A3IV Definitions */
#define TA0IV_NONE          (0x0000)    /* No Interrupt pending */
#define TA0IV_TACCR1        (0x0002)    /* TA0CCR1_CCIFG */
#define TA0IV_TACCR2        (0x0004)    /* TA0CCR2_CCIFG */
#define TA0IV_6             (0x0006)    /* Reserved */
#define TA0IV_8             (0x0008)    /* Reserved */
#define TA0IV_TAIFG         (0x000A)    /* TA0IFG */

/************************************************************
* USI
************************************************************/
#define __MSP430_HAS_USI__            /* Definition to show that Module is available */

#define USICTL0_              0x0078    /* USI  Control Register 0 */
sfrb(USICTL0, USICTL0_);
#define USICTL1_              0x0079    /* USI  Control Register 1 */
sfrb(USICTL1, USICTL1_);
#define USICKCTL_             0x007A    /* USI  Clock Control Register */
sfrb(USICKCTL, USICKCTL_);
#define USICNT_               0x007B    /* USI  Bit Counter Register */
sfrb(USICNT, USICNT_);
#define USISRL_               0x007C    /* USI  Low Byte Shift Register */
sfrb(USISRL, USISRL_);
#define USISRH_               0x007D    /* USI  High Byte Shift Register */
sfrb(USISRH, USISRH_);
#define USICTL_               0x0078    /* USI  Control Register */
sfrw(USICTL, USICTL_);
#define USICCTL_              0x007A    /* USI  Clock and Counter Control Register */
sfrw(USICCTL, USICCTL_);
#define USISR_                0x007C    /* USI  Shift Register */
sfrw(USISR, USISR_);

#define USIPE7              (0x80)    /* USI  Port Enable Px.7 */
#define USIPE6              (0x40)    /* USI  Port Enable Px.6 */
#define USIPE5              (0x20)    /* USI  Port Enable Px.5 */
#define USILSB              (0x10)    /* USI  LSB first  1:LSB / 0:MSB */
#define USIMST              (0x08)    /* USI  Master Select  0:Slave / 1:Master */
#define USIGE               (0x04)    /* USI  General Output Enable Latch */
#define USIOE               (0x02)    /* USI  Output Enable */
#define USISWRST            (0x01)    /* USI  Software Reset */

#define USICKPH             (0x80)    /* USI  Sync. Mode: Clock Phase */
#define USII2C              (0x40)    /* USI  I2C Mode */
#define USISTTIE            (0x20)    /* USI  START Condition interrupt enable */
#define USIIE               (0x10)    /* USI  Counter Interrupt enable */
#define USIAL               (0x08)    /* USI  Arbitration Lost */
#define USISTP              (0x04)    /* USI  STOP Condition received */
#define USISTTIFG           (0x02)    /* USI  START Condition interrupt Flag */
#define USIIFG              (0x01)    /* USI  Counter Interrupt Flag */

#define USIDIV2             (0x80)    /* USI  Clock Divider 2 */
#define USIDIV1             (0x40)    /* USI  Clock Divider 1 */
#define USIDIV0             (0x20)    /* USI  Clock Divider 0 */
#define USISSEL2            (0x10)    /* USI  Clock Source Select 2 */
#define USISSEL1            (0x08)    /* USI  Clock Source Select 1 */
#define USISSEL0            (0x04)    /* USI  Clock Source Select 0 */
#define USICKPL             (0x02)    /* USI  Clock Polarity 0:Inactive=Low / 1:Inactive=High */
#define USISWCLK            (0x01)    /* USI  Software Clock */

#define USIDIV_0            (0x00)    /* USI  Clock Divider: 0 */
#define USIDIV_1            (0x20)    /* USI  Clock Divider: 1 */
#define USIDIV_2            (0x40)    /* USI  Clock Divider: 2 */
#define USIDIV_3            (0x60)    /* USI  Clock Divider: 3 */
#define USIDIV_4            (0x80)    /* USI  Clock Divider: 4 */
#define USIDIV_5            (0xA0)    /* USI  Clock Divider: 5 */
#define USIDIV_6            (0xC0)    /* USI  Clock Divider: 6 */
#define USIDIV_7            (0xE0)    /* USI  Clock Divider: 7 */

#define USISSEL_0           (0x00)    /* USI  Clock Source: 0 */
#define USISSEL_1           (0x04)    /* USI  Clock Source: 1 */
#define USISSEL_2           (0x08)    /* USI  Clock Source: 2 */
#define USISSEL_3           (0x0C)    /* USI  Clock Source: 3 */
#define USISSEL_4           (0x10)    /* USI  Clock Source: 4 */
#define USISSEL_5           (0x14)    /* USI  Clock Source: 5 */
#define USISSEL_6           (0x18)    /* USI  Clock Source: 6 */
#define USISSEL_7           (0x1C)    /* USI  Clock Source: 7 */

#define USISCLREL           (0x80)    /* USI  SCL Released */
#define USI16B              (0x40)    /* USI  16 Bit Shift Register Enable */
#define USIIFGCC            (0x20)    /* USI  Interrupt Flag Clear Control */
#define USICNT4             (0x10)    /* USI  Bit Count 4 */
#define USICNT3             (0x08)    /* USI  Bit Count 3 */
#define USICNT2             (0x04)    /* USI  Bit Count 2 */
#define USICNT1             (0x02)    /* USI  Bit Count 1 */
#define USICNT0             (0x01)    /* USI  Bit Count 0 */
/************************************************************
* WATCHDOG TIMER
************************************************************/
#define __MSP430_HAS_WDT__            /* Definition to show that Module is available */

#define WDTCTL_               0x0120    /* Watchdog Timer Control */
sfrw(WDTCTL, WDTCTL_);
/* The bit names have been prefixed with "WDT" */
#define WDTIS0              (0x0001)
#define WDTIS1              (0x0002)
#define WDTSSEL             (0x0004)
#define WDTCNTCL            (0x0008)
#define WDTTMSEL            (0x0010)
#define WDTNMI              (0x0020)
#define WDTNMIES            (0x0040)
#define WDTHOLD             (0x0080)

#define WDTPW               (0x5A00)

/* WDT-interval times [1ms] coded with Bits 0-2 */
/* WDT is clocked by fSMCLK (assumed 1MHz) */
#define WDT_MDLY_32         (WDTPW+WDTTMSEL+WDTCNTCL)                         /* 32ms interval (default) */
#define WDT_MDLY_8          (WDTPW+WDTTMSEL+WDTCNTCL+WDTIS0)                  /* 8ms     " */
#define WDT_MDLY_0_5        (WDTPW+WDTTMSEL+WDTCNTCL+WDTIS1)                  /* 0.5ms   " */
#define WDT_MDLY_0_064      (WDTPW+WDTTMSEL+WDTCNTCL+WDTIS1+WDTIS0)           /* 0.064ms " */
/* WDT is clocked by fACLK (assumed 32KHz) */
#define WDT_ADLY_1000       (WDTPW+WDTTMSEL+WDTCNTCL+WDTSSEL)                 /* 1000ms  " */
#define WDT_ADLY_250        (WDTPW+WDTTMSEL+WDTCNTCL+WDTSSEL+WDTIS0)          /* 250ms   " */
#define WDT_ADLY_16         (WDTPW+WDTTMSEL+WDTCNTCL+WDTSSEL+WDTIS1)          /* 16ms    " */
#define WDT_ADLY_1_9        (WDTPW+WDTTMSEL+WDTCNTCL+WDTSSEL+WDTIS1+WDTIS0)   /* 1.9ms   " */
/* Watchdog mode -> reset after expired time */
/* WDT is clocked by fSMCLK (assumed 1MHz) */
#define WDT_MRST_32         (WDTPW+WDTCNTCL)                                  /* 32ms interval (default) */
#define WDT_MRST_8          (WDTPW+WDTCNTCL+WDTIS0)                           /* 8ms     " */
#define WDT_MRST_0_5        (WDTPW+WDTCNTCL+WDTIS1)                           /* 0.5ms   " */
#define WDT_MRST_0_064      (WDTPW+WDTCNTCL+WDTIS1+WDTIS0)                    /* 0.064ms " */
/* WDT is clocked by fACLK (assumed 32KHz) */
#define WDT_ARST_1000       (WDTPW+WDTCNTCL+WDTSSEL)                          /* 1000ms  " */
#define WDT_ARST_250        (WDTPW+WDTCNTCL+WDTSSEL+WDTIS0)                   /* 250ms   " */
#define WDT_ARST_16         (WDTPW+WDTCNTCL+WDTSSEL+WDTIS1)                   /* 16ms    " */
#define WDT_ARST_1_9        (WDTPW+WDTCNTCL+WDTSSEL+WDTIS1+WDTIS0)            /* 1.9ms   " */

/* INTERRUPT CONTROL */
/* These two bits are defined in the Special Function Registers */
/* #define WDTIE               0x01 */
/* #define WDTIFG              0x01 */

/************************************************************
* Calibration Data in Info Mem
************************************************************/

#ifndef __DisableCalData

#define CALDCO_16MHZ_         0x10F8    /* DCOCTL  Calibration Data for 16MHz */
const_sfrb(CALDCO_16MHZ, CALDCO_16MHZ_);
#define CALBC1_16MHZ_         0x10F9    /* BCSCTL1 Calibration Data for 16MHz */
const_sfrb(CALBC1_16MHZ, CALBC1_16MHZ_);
#define CALDCO_12MHZ_         0x10FA    /* DCOCTL  Calibration Data for 12MHz */
const_sfrb(CALDCO_12MHZ, CALDCO_12MHZ_);
#define CALBC1_12MHZ_         0x10FB    /* BCSCTL1 Calibration Data for 12MHz */
const_sfrb(CALBC1_12MHZ, CALBC1_12MHZ_);
#define CALDCO_8MHZ_          0x10FC    /* DCOCTL  Calibration Data for 8MHz */
const_sfrb(CALDCO_8MHZ, CALDCO_8MHZ_);
#define CALBC1_8MHZ_          0x10FD    /* BCSCTL1 Calibration Data for 8MHz */
const_sfrb(CALBC1_8MHZ, CALBC1_8MHZ_);
#define CALDCO_1MHZ_          0x10FE    /* DCOCTL  Calibration Data for 1MHz */
const_sfrb(CALDCO_1MHZ, CALDCO_1MHZ_);
#define CALBC1_1MHZ_          0x10FF    /* BCSCTL1 Calibration Data for 1MHz */
const_sfrb(CALBC1_1MHZ, CALBC1_1MHZ_);

#endif /* #ifndef __DisableCalData */


/************************************************************
* Interrupt Vectors (offset from 0xFFE0)
************************************************************/

#define PORT1_VECTOR            ( 3)                     /* 0xFFE4 Port 1 */
#define PORT2_VECTOR            ( 4)                     /* 0xFFE6 Port 2 */
#define USI_VECTOR              ( 5)                     /* 0xFFE8 USI */
#define TIMER0_A1_VECTOR        ( 9)                     /* 0xFFF0 Timer0_A CC1, TA */
#define TIMER0_A0_VECTOR        (10)                     /* 0xFFF2 Timer0_A CC0 */
#define WDT_VECTOR              (11)                     /* 0xFFF4 Watchdog Timer */
#define NMI_VECTOR              (15)                     /* 0xFFFC Non-maskable */
#define RESET_VECTOR            ("reset")                /* 0xFFFE Reset [Highest Priority] */

/************************************************************
* End of Modules
************************************************************/
#ifdef __cplusplus
}
#endif /* extern "C" */

#endif /* #ifndef __MSP430G2302 */

